TIPS ABOUT HOW TO Extend Smok Pen Recharge Time
The Smok Pen is really a new pen that was developed by two guys in California. They wished to develop a cool writing instrument that appeared as if a genuine pen but had the ability to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has taken the marketplace by storm.
The Smok Pen has a built quality that’s just great. I came across that even though it is an electronic pen the build quality is just as good as any of the pens that I’ve reviewed. For the reason that of how they made the most notable cap. You don’t need to be worried about the cap cracking or breaking on you Smok Valve Pen.
The two biggest differences that separate the Smok Valve from other pens may be the shape of the coils and just how that they are built. Generally the coil on a Smok Pen is larger than on other pens. I believe that they did this on purpose, to make the pen feel bigger.
If you take a look at a Smok Pen, you will observe that the body of the pen is round and not smooth like other pens. On the trunk of the pen there is a little tab that houses the coil. Once you press on the tab you can actually turn the heating element on and off. I must say i liked this feature since it allows me to utilize the Smok Pen 22 whenever I feel like smoking.
To utilize the Smok Pen you need to keep carefully the heat button pressed. After the button is pressed, the heating element will begin to warm up. Once it gets to the appropriate temperature it is possible to turn off the heating element. Smok recommends utilizing a 22mm tank. I prefer a larger tank, but that’s just me.
Once you put your Smok Pen into the tank you will see a indicator light come on. The indicator light will remain green unless you put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is very important always put your pen into the charger before you Juul Compatible Pods apply the e-liquids to the coil heads. Additionally it is important to do that before putting your e-liquids into the coil heads.
After you have completed this step, it is best to check to see for anyone who is at the proper temperature for the coils to fire. If not then you should turn the power off and try again. If you are still not satisfied with your Smok Pen i quickly suggest you take it set for some troubleshooting. This is exactly what I’d call the “troubleshooting process” because sometimes things just do not work as they should. I would recommend that you perform the following two steps, then go ahead and check the Smok Pen to see if it still has the electronic charging port.
Before you go any further you should take away the battery from your own pen and unscrew the magnetic cap. You need to then take away the plastic sleeve that holds the sub-ohm. There exists a wire that runs through the Smok’s body which is green in color. You need to loosen this wire using pliers. Once you have loosened this wire after that you can access the sub-ohm. You need to then remove the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful never to touch the coils.
After you have placed the sub-ohm tank into the pen you need to then place the rest of the components like the wattage, the batteries and the heating element into the included microwaveable microwave oven. Start the power and follow the on screen instructions. You need to place the pen’s battery into the microwave and activate the setting. You should then wait approximately 30 seconds before turning it back off. When you first put the pen in to the microwave the electronic reading will show a minimal voltage protection setting. If this setting will not automatically get set then you should follow the on screen instructions.
Once the Smok Pen has already reached the temperature that it requires to reach you need to then connect the two wires to the negative and positive on the positive post on the Smok unit. You should then connect the other end of the battery to the negative post on the negative side of the Smok unit. The final step would be to connect the positive cable to underneath of the Smok’s power switch.
After all the components have been placed in to the pen, you should turn the energy on. Following the first test run, you ought to be able to see the battery life indicator light come on. If you do not see any sign of life from the Smok Pen, you need to remove the battery from the pen and replace it with a fresh one. For your convenience gleam green light which might be pressed in order to confirm the battery charging status. When you have done these things and you do not start to see the green light indicating charging, you should replace the battery.